tb2705, Instrukcje, National INSTRUMENTS, Pdf
[ Pobierz całość w formacie PDF ]
E Series Multifunction DAQ
Accessories and Cables
Selection Guide
Step 1.
Select your E Series device.
Step 2.
Using Tables 1 and 2 as a guide, determine which
accessories are appropriate for that device. Select an accessory. Use
Table 3 as a general reference about accessories for E Series devices.
Step 3.
Using Tables 1 and 2, determine which cable is required to
connect your selected device and accessory.
Accessory
TBX-68, CB-68LP, CB-68LPR,
DAQ Signal Accessory, CA-1000,
BNC-2110, BNC-2120,
BNC-2090, SCB-68
TB-2705
SCXI, Signal Conditioning
SCC Modular Signal Conditioning
Device
Cables
68-pin E Series
SH68-68-EP (shielded)
Connects directly to the device
See page 464 for
See page 550 for SCC Modular
(except DAQCard)
R6868 (unshielded)
(PXI only)
SCXI Signal Conditioning details
Signal Conditioning details
SHC68U-68-EP (shielded)
N/A
See page 464 for
See page 550 for SCC Modular
Top
Slot
Bottom
Slot
Latching DAQCards
RC68-68 (unshielded)
SCXI Signal Conditioning details
Signal Conditioning details
NI 6024E, NI 6062E
SHC68-68-EP (shielded)
RC68-68 (unshielded)
Nonlatching DAQCards
PSHR68-68 (shielded)
N/A
See page 464 for
See page 550 for SCC Modular
AI-16E-4, AI-16XE-50
PR68-68F (unshielded)
SCXI Signal Conditioning details
Signal Conditioning details
Table 1. Accessories and Cables for 68-pin and DAQCard E Series Devices
Accessory
TBX-68, CB-68LP, CB-68LPR,
DAQ Signal Accessory, CA-1000,
TBX-68, CB-68LP
SCC Modular
BNC-2110, BNC-2120,
CB-68LPR, CA-1000,
SCXI Signal
Signal
BNC-2090, SCB-68
BNC-2115
SCB-68
SCB-100
Conditioning
Conditioning
Device
Cables
100-pin E Series with
SH1006868 (shielded); splits into two
SH1006868 (shielded); splits SH1006868 (shielded); splits
SH100100
See page 464 for
See page 550 for
64 AI channels
68-pin connectors; these accessories
into two 68-pin connectors;
into two 68-pin connectors;
(shielded)
SCXI Signal
SCC Modular Signal
NI 6071E, NI 6031E, NI 6033E
are used with the first 68-pin connector.
these accessories are used
these accessories are used
Conditioning details
Conditioning details
AT-MIO-64E-3
See Figure 16 on page 338.
with the second 68-pin
with the second 68-pin
connector.
connector.
100-pin E Series with
SH1006868 (shielded); splits ino two
N/A
SH1006868 (shielded); splits
SH100100
See page 464 for
See page 550 for
16 AI channels
68-pin connectors; these accessories
into two 68-pin connectors;
(shielded)
SCXI Signal
SCC Modular Signal
and 32 DIO lines
are used with the first 68-pin connector.
these accessories are used
Conditioning details
Conditioning details
PCI-6025E, AT-MIO-16DE-10
See Figure 16 on page 338.
with the second 68-pin
connector.
Table 2. Accessories and Cables for 100-pin and DAQCard E Series Devices
Accessory
Decription
Page
SCXI Signal Conditioning
High channel count signal conditioning platform
464
SCC Modular Signal Conditioning
Single or dual channel signal conditioning modules
550
AMUX-64T, 5B, SSR, ER, and
External signal conditioning accessories
575-588
SC-204x Signal Conditioning
BNC-2110
BNC accessory for 68-pin E Series devices
335
BNC-2115
BNC accessory for 100-pin E Series devices
335
BNC-2120
BNC accessory with function generator
335
BNC-2090
Rack mountable BNC accessory
335
CA-1000 enclosure
Configurable connectivity enclosure
341
TB-2705
Latching screw-terminal block for PXI E Series modules
336
SCB-100
100-pin, shielded screw terminal block with
336
breadboard areas
SCB-68
68-pin, shielded screw terminal block with breadboard areas
336
TBX-68
68-pin, DIN rail mountable screw terminal block
336
CB-68LP, CB-68LPR
68-pin, low-cost screw terminal block
337
Signal Source and Demo Accessory
DAQ signal accessory to demo and test analog,
337
digital and counter/timer functions
For complete and up-to-date information about accessories, visit
ni.com/catalog
Table 3. Overview of E Series DAQ Accessories
334
National Instruments
Tel: (512) 794-0100 • Fax: (512) 683-9300 • info@ni.com • ni.com
E Series Multifunction DAQ
Accessories and Cables
SCXI High-Performance Signal Conditioning
(see Figure 1)
SCXI is a modular high-performance signal conditioning platform that you use as a front
end to your E Series DAQ device. With the SCXI multiplexing architecture, you can expand
your analog inputs to 3,072 channels. Additionally, SCXI offers a variety of modules for
connecting to thermocouples, RTDs, strain gauge transducers, LVDT position sensors,
ICP-compatible accelerometers/microphones, thermistors, millivolt inputs, voltage inputs
up to 1000 V, current inputs (0-20mA), frequency inputs or dynamic signals. See page 464
for details on SCXI Signal Conditioning.
SCC Series – Modular Signal Conditioning for
Low-Channel Count Applications
(see Figure 2)
The SCC Series modular signal conditioning system consists of SCC modules that plug into
a low-profile SC-2345 shielded carrier. SCC modules give you single or dual-channel signal
conditioning for up to 16 analog input channels and eight digital I/O lines of your plug in
E Series DAQ device. The SCC Series offers signal conditioning for a variety of inputs,
including thermocouples, RTDs, strain gauges, ICP-compatible accelerometers,
accelerators, analog inputs requiring isolation, high-voltage (up to 100V), current
(0-20mA), and optically isolated digital I/O. Lowpass filtering and bread-boarding modules
are also available. See page 550 for details on SCC Signal Conditioning.
Figure 1. SCXI High-Performance
Signal Conditioning
Connector Blocks
BNC-2100 Series Connector Blocks
(see Figure 3)
The BNC-2100 Series are shielded connector blocks with signal-labeled BNC connectors for
easy connectivity of your analog input, analog output, digital I/O and counter/timer
signals to your E Series device. The BNC-2110 and BNC-2120 work with all E Series devices.
The BNC-2120 also provides a function generator, quadrature encoder, temperature
reference, thermocouple connector and LED so you can test the functionality of your
hardware. The BNC-2115 has 24 BNC inputs for connecting to the extended analog input
channels of our 100-pin E Series DAQ devices.
BNC-2110 ..................................................................................................777643-01
Dimensions – 20.3 by 11.2 by 5.5 cm (8.0 by 4.4 by 2.2 in.)
BNC-2115 ..................................................................................................777807-01
Dimensions – 20.3 by 11.2 by 5.5 cm (8.0 by 4.4 by 2.2 in.)
BNC-2120 ..................................................................................................777960-01
Dimensions – 26.7 by 11.2 by 6.0 cm (10.5 by 4.4 by 2.4 in.)
Figure 2. SCC Portable, Modular
Signal-Conditioning
BNC-2090 Shielded BNC Adapter Chassis
(see Figure 4)
The BNC-2090 is a shielded, rack-mountable adapter with signal-labeled BNC connectors,
spring terminal blocks, and component locations for passive signal conditioning. The
BNC-2090 consists of 22 BNC connectors and 28 spring terminals to simplify connection
to your analog, digital, trigger and counter/timer signals. It also has silk-screened
component locations that you use to develop simple signal conditioning circuits.
For added flexibility, you can connect any E Series DAQ devices to the BNC-2090 from the
front or rear through dual 68-pin connectors.
Dimensions – 48.3 by 4.4 by 18.8 cm (19.0 by 1.7 by 7.4 in.)
BNC-2090...................................................................................................777270-01
Figure 3. BNC-2100 Series Connector Blocks
Figure 4. BNC-2090 Shielded BNC
Adapter Chassis
National Instruments
Tel: (512) 794-0100 • Fax: (512) 683-9300 • info@ni.com • ni.com
335
E Series Multifunction DAQ
Accessories and Cables
CA-1000 Configurable Signal Conditioning Enclosure
(see Figure 5)
The CA-1000 is a configurable enclosure that gives you maximum user-defined connectivity
and flexibility through customized panelettes. Each enclosure can accommodate up to 9
panelettes. See page 341 for more information about the CA-1000.
Dimensions – 30.7 by 25.4 by 4.3 cm (21.1 by 10 by 1.7 in.
CA-1000......................................................................................................see page 341
TB-2705 Terminal Block for 68-pin PXI E Series Devices
(see Figure 6)
The TB-2705 is a screw terminal block for PXI that works with your PXI E Series DAQ devices.
It latches to the front of your PXI module with locking screws and provides strain relief as
well as easy access to your analog, digital, trigger and counter/timer signals through screw
terminals. Dimensions – 8.43 by 10.41 by 2.03 cm (3.32 by 4.1 by 0.8 in.)
TB-2705......................................................................................................778241-01
Figure 5. CA-1000 Configurable Signal
Conditioning Enclosure
SCB-68 and SCB-100 Shielded I/O Connector Blocks
(see Figure 7)
The SCB-68 and SCB-100 are shielded I/O connector blocks for rugged, very low-noise
signal termination for connecting to 68-pin or 100-pin E Series DAQ devices, respectively.
They have silk-screened component locations for easy addition of simple signal
conditioning circuitry for your analog input channels. They also include general-purpose
breadboard areas (two on the SCB-68; three on the SCB-100) as well as an IC temperature
sensor for cold junction compensation in temperature measurements.
SCB-68........................................................................................................776844-01
Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.)
SCB-100......................................................................................................776990-01
Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.)
Figure 6. TB-2705 Terminal Block
TBX-68 I/O Connector Block with DIN-Rail Mounting
(see Figure 8)
Termination accessory with 68 screw terminals for easy connection of field I/O signals to
68-pin DAQ devices. Includes one 68-pin male connector for direct connection to 68-pin
cables. The TBX-68 is mounted in a protective plastic base with hardware for mounting on
a standard DIN rail. Dimensions – 12.50 by 10.74 cm (4.92 by 4.23 in.)
TBX-68........................................................................................................777141-01
Figure 7. SCB-68 and SCB-100 Shielded
I/O Connector Blocks
Figure 8. TBX-68 I/O Connector Block
336
National Instruments
Tel: (512) 794-0100 • Fax: (512) 683-9300 • info@ni.com • ni.com
E Series Multifunction DAQ
Accessories and Cables
CB-68LP and CB-68LPR I/O Connector Blocks
(see Figure 9)
Low-cost termination accessory with 68 screw terminals for easy connection of field
I/O signals to 68-pin E Series DAQ devices. Includes one 68-pin male connector for direct
connection to 68-pin cables. The connector blocks include standoffs for use on a desktop
or mounted in a custom panel. The CB-68LP has a vertical mounted 68-pin connector.
The CB-68LPR has a right-angle mounted connector, and is used with the CA-1000 (see
page 341).
CB-68LP dimensions – 14.35 by 10.74 cm (5.65 by 4.23 in.)
CB-68LPR dimensions – 7.62 by 16.19 cm (3.00 by 6.36 in.)
CB-68LP......................................................................................................777145-01
CB-68LPR ..................................................................................................777145-02
Figure 9. CB-68LP and CB-68LPR I/O
Connector Blocks
Signal Source and Demo Accessory
(see Figure 10)
The DAQ Signal Accessory demonstrates and tests the use of analog, digital, and
counter/timer functions of DAQ devices. You can connect the DAQ Signal Accessory
directly to your DAQ device. It features a built-in function generator, quadrature encoder,
solid-state relay, IC temperature sensor, noise generator, microphone jack, thermocouple
jack, four LEDs, and a digital trigger button. The DAQ Signal Accessory works with all
E Series DAQ devices. Dimensions – 12.7 by 12.7 cm (5.0 by 5.0 in.)
DAQ Signal Accessory ................................................................................777382-01
Figure 10. DAQ Signal Accessory
RTSI Bus Cables
(see Figures 11 and 12)
Use RTSI cables to connect timing and synchronization signals among Measurement,
Vision, Motion, and CAN devices. For systems using long and short devices, order the
extended RTSI cable.
2 devices ....................................................................................................776249-02
3 devices ...................................................................................................776249-03
4 devices ...................................................................................................776249-04
5 devices ....................................................................................................776249-05
Extended, 5 devices ....................................................................................777562-05
Figure 11. RTSI Bus Cable
Shielded I/O Cables
SH68-68-EP Shielded Cable
(see Figure 13)
Shielded 68-conductor cable terminated with two 68-pin female 0.050 series D-type
connectors. Features individually shielded analog twisted pairs for reduced crosstalk
with high-speed devices. This cable works with all 68-pin E Series devices (except
latching DAQCards). If you need a right-angle connector, the SH68-68R1 shielded cable is
fully compatible.
1 m ............................................................................................................184749-01
2 m ............................................................................................................184749-02
Figure 12. Extended RTSI Bus Cable
Figure 13. SH68-68-EP Shielded Cable
National Instruments
Tel: (512) 794-0100 • Fax: (512) 683-9300 • info@ni.com • ni.com
337
E Series Multifunction DAQ
Accessories and Cables
SH68-68R1 Shielded Cable
(see Figure 14)
Shielded 68-conductor cable; one end terminates with a 68-pin female 0.050 series D-type
connector and the other end terminates with a right-angle 68-pin female 0.050 series
D-type connector.
1 m ............................................................................................................185785-01
SH100100 Shielded Cable
(see Figure 15.
Shielded 100-conductor cable terminated with 100-pin male 0.050 series D-type
connectors. This cable connects the 100-pin E Series devices to 100-pin accessories.
1 m ............................................................................................................182853-01
2 m ............................................................................................................182853-02
Figure 14. SH68-68R1 Shielded Cable
SH1006868 Shielded Cable
(see Figure 16)
Shielded cable that connects to the 100-pin E Series devices and terminates with two
female 68-pin 0.050 series D-type connectors. See Table 2 on page 334 for accessories
compatible with each 68-pin connector.
1 m ............................................................................................................182849-01
2 m ............................................................................................................182849-02
Figure 15. SH100100 Shielded Cable
SHC68-68-EP and SHC68U-68-EP Shielded Cables
for Latching E Series DAQCards
(see Figure 17)
These cables connect a latching E Series DAQCard (NI 6062E and NI 6024E) to standard
68-pin accessories. Latching screws secure the shielded connector to the PCMCIA
DAQCard for stability. The SHC68-68-EP is a shielded 68-conductor cable terminated with
a VHDCI 68-pin male connector at one end and a 68-pin female 0.050 series D-type
connector at the other. The SHC68U-68-EP is identical to the SHC68-68-EP except it uses
an
inverted
VHDCI 68-pin male connector. Use the SHC68-68-EP for a DAQCard located
in the bottom PCMCIA slot in your laptop. Use the SHC68U-68-EP cable with a
DAQCard inserted in the upper PCMCIA slot in your laptop. When using two E Series
DAQCard PCMCIA devices in adjacent slots, you must use one SHC68-68-EP
and
one SHC68U-68-EP.
SHC68-68-EP
50 cm ..................................................................................................186838-0R5
1 m ........................................................................................................186838-01
SHC68U-68-EP
50 cm ..................................................................................................187406-0R5
1 m ........................................................................................................187406-01
Figure 16. SH1006868 Shielded Cable
Figure 17. SHC68-68-EP Shielded Cable
PSHR68-68 Shielded Cable Kit for Nonlatching DAQCards
(see Figure 18)
Shielded cable for use in connecting non-latching E Series DAQCards (AI-16E-4 and
AI-16XE-50) with 68-pin accessories. The kit contains the PSHR68-68M, the PCMCIA Strain-
Relief Adapter and a 1 m SH68-68-EP cable.
1m ............................................................................................................777293-01
Figure 18. PSHR68-68 Shielded Cable Kit
PSHR68-68M Shielded Cable for Nonlatching DAQCards
(see Figure 19)
Shielded cable for use in connecting non-latching E Series DAQCards (AI-16E-4 and
AI-16XE-50) with custom cables and other 68-pin cable assemblies.
10 cm ........................................................................................................183569-01
Figure 19. PSHR68-68M Shielded Cable
338
National Instruments
Tel: (512) 794-0100 • Fax: (512) 683-9300 • info@ni.com • ni.com
[ Pobierz całość w formacie PDF ]